iFlight BLITZ F7 45A 2-6S Stack
by iFlight
Sold out
Original price
$0.00
-
Original price
$0.00
Original price
$0.00
$216.00
$216.00
-
$283.00
Current price
$216.00
free return
Do you live in Belgium or The Netherlands? Then you can return your package for free!
Out of stock
Out of stock
Description
Characteristics
- Improved circuit design, better components and less electrical noise!
- DJI HD VTX connector (Plug-and-Play / no soldering required)
- FC indicator LEDs for visual troubleshooting
- Met LC-filter
| BLITZ F7 V1.1 Flight Controller | |
| MCU | STM32 F722 |
| Gyro | BMI270 |
| Barometer | DPS310 |
| OSD Chip | AT7456E |
| Flash | 32 MB (Blackbox-flash) |
| UARTS | 6 |
| Motor outputs | 4x (SH1.0 connector) |
| I2C-serial | SDA / SLA-pads |
| Smartaudio / IRC Tramp VTX protocol supported | |
| LED-controller | And |
| Beeper-pad | And |
| Firmware target | IFRC-IFLIGHT_BLITZ_F722 |
| Montagepatroon | 30.5 x 30.5 mm / 4 mm PCB-gatdiameter |
| Dimensions | 36.5 x 35 mm |
| Weight | 7.8 g |
Wiring suggestion
- UART 1 for VTX HD / Analog
- UART 2 for a receiver
- UART 3/4/5 for GPS or other sensors that require a serial port
- UART 6 for ESC telemetry
Tips
- 1. F722 MCU has an internal inverter.
- 2. SBUS、CRSF、ELRS、IBUS、DSM ETC... can be connected to any unused UART_RX, we suggest you connect to Uart_RX2
- 3. Frsky SmartPort, Tramp & Smartaudio can be connected to any unused UART_TX, we suggest you connect to Uart_TX1
- 4. F.port can be connected to any unused UART_TX, we suggest you connect to Uart_TX2
| BLITZ E45S 4-IN-1 2-6S ESC | |
| Support | DShot150/300/600/MultiShot/OneShot etc. |
| assembly gate | 30.5 x 30.5 mm / Φ4 mm |
| Supports | 2-6S liposuction |
| Telemetry output | Nee |
| Goal | QH-40 16.7 |
| Current sensor | And |
| Constant current | 45 amps |
| Flow assessment | 200 |
| Burst | 55 amps |
| Weight | 14.7 g |
| MCU | BB21 |
| BEC | Nee |
Characteristics
- Stable output power
- 4 power levels up to 1600mW
- 40 channels (including Raceband)
- Fast frequency locking, no startup interference with other pilots
- Built-in output power self-check function
- VTX telemetry with IRC Tramp protocol
- VTX is set to 25mW by default! Power levels above 25mW require a HAM license or local authority approval! Make sure you are flying legal frequencies and use our prepared Betaflight VTX tables for your area.
| BLITZ 1.6W VTX adjustable | |
| Input voltage | 7V～36V |
| Interface | MMCX |
| Power levels | PIT/25mW/400mW/800mW/1600mW |
| Channels | 40 (including Race Tire) |
| Montagepatroon | 30.5 x 30.5 mm / Φ3 |
| lightweight | 18.9 g (excluding antenna) |
| VTX telemetry | IRC Tramp |
| Betaflight IRC Tramp Configuration | Download the attached VTX table for Betaflight! |
| All VTX tables can also be found here | LINK |
| IRC Tramp VTX-tabelwaarden | 25mW/400mW/800mW/1600mW |
What's included:
- 1 PC X BLITZ F7 V1.1 FLIGHT CONTROLLER
- 1PC BLITZ E45S 4-IN-1 2-6S ESC
- 1PC X BLITZ 1.6W VTX Adjustable
- 1 SET X SILICON TRANSMITTERS
- 1SET X WIRING HARNESS FOR F7 FLIGHT CONTROLLER